Your objective is to design the cheapest possible bridge to span a highway. The total span of the bridge (across both halves of the highway) must be L = 30 meters, and it must support its own weight and a load q = 33 × 10^4 N/m along its span (a total load of about 1 × 10^6 N plus its own weight). The bridge span will be supported by between one and four I-beams. In the figure above.The I-beams would be parallel to each other going into the page, for example it could be one Ibeam in the middle of the bridge, or one I-beam on both sides of the bridge, etc. and this will be represented by the design variable, nIbeams. The shape of the I-beams will be represented by three continuous design variables, the height, h, the flange width, b, and thickness, t. The middle support will be rectangular (when viewed from above), and will have two design variables, the width, w, and depth, d. Let, ρIbeams be the density of the material used for the I-beams.

Your objective is to design the cheapest possible bridge to span a highway. The total span of the bridge (across both halves of the highway) must be L = 30 meters, and it must support its own weight a

g) In a binary encoded GA with two design variables, one with 4-bits, and one with 16 bits, what is the total number of possible population members? (a) 2 18 (b) 2 20 (c) 2 24 (d) 2 32 (a-2) Your objective is to design the cheapest possible bridge to span a highway. The total span of the bridge (across both halves of the highway) must be L= 30 meters, and it must support its own weight and a load q= 33 10 4 N/m along its span (a total load of about 1 10 6 N plus its own weight). The bridge span will be supported by between one and four I-beams. In the gure above, the I-beams would be parallel to each other going into the page, for example it could be one I- beam in the middle of the bridge, or one I-beam on both sides of the bridge, etc. and this will be represented by the design variable, n Ibeams . The shape of the I-beams will be represented by three continuous design variables, the height, h, the ange width, b, and thickness, t. The middle support will be rectangular (when viewed from above), and will have two design variables, the width, w, and depth, d. Let, r Ibeams be the density of the material used for the I-beams, then the mass of the I-beams can be computed using, MIbeams = [ 2bt + ( h 2t) t] L r Ibeams n Ibeams : Let r Support be the density of the material used for the support, and H=5m be the height of the bridge above the ground, then the mass of the middle support can be computed using MSupport = wd H r Support : There is a constraint that the stress of the I-beam is less than the material failure stress for the I-beam, s Failure-Ibeams . (Note: gis the gravitational constant (9.81 m/s 2 ).) s Ibeams =q L 2 2 + M Ibeams L 4 g 8 I Ibeam n Ibeams h 2 s Failure-Ibeams ; where I I beam is the moment of inertia for the I-beam given by IIbeam =( h 2t) 3 t 12 + 2″ t3 b 12 + t b h 2 t 2 2# : In addition, there is a constraint that the shear stress in the I-beams is less than the material failure stress: tIbeams = M Ibeams g + qL 4 [2 bt + ( h 2t) t] n Ibeams s Failure-Ibeams : For the middle support there are two constraints, the column cannot buckle and the stress must be less than the material failure stress. Buckling is based on a requirement that the applied load is less than a critical load: PApplied =M Ibeams g + qL 2 P Crit ; where the critical load is a function of th slowest moment of inertia of the support and the modulus of elasticity of the support material, E support , P Crit =p 2 E Support minn w3 d 12 ;wd 3 12 o 4 H 2 : The stress requirement is that the applied stress is less than the support material failure stress, sSupport =P Applied wd s Failure-Support : The bridge span (I-beams) can be made from A1 6061, A36 Steel, A514 Steel, or Titanium; how- ever, the support can be made from A1 6061, A36 Steel, A514 Steel, or Concrete. The reason for the difference is that concrete cannot be loaded in tension. The material properties and prices are listed in the Table: Material Density (kg/m 3 ) Modulus of Elasticity (GPa = 10 9 N/m 2 ) Failure Stress (MPa = 10 6 N/m 2 ) Cost($/kg) A1 6061 2700 70 270 2.05 A36 Steel 7850 210 250 0.62 A514 Steel 7900 210 700 0.90 Titanium 4500 120 760 16.00 Concrete 2400 31 70 0.04 Your objective is to nd the dimensions of the I-beams, number of I-beams, and material type for the I-beams, as well as the dimensions of the support and material type for the support to minimize cost of the bridge. Where c Ibeams and c Support are the cost per kilogram of the materials used for the I-beams and Support. The total bridge cost is then: C= c Ibeams M Ibeams + c Support M Support : (a) Please explain what optimization algorithm you chose to nd the cheapest possible bridge and why. (b) What are the design variables and cost for the cheapest bridge?

#### Why Choose Us

- 100% non-plagiarized Papers
- 24/7 /365 Service Available
- Affordable Prices
- Any Paper, Urgency, and Subject
- Will complete your papers in 6 hours
- On-time Delivery
- Money-back and Privacy guarantees
- Unlimited Amendments upon request
- Satisfaction guarantee

#### How it Works

- Click on the “Place Order” tab at the top menu or “Order Now” icon at the bottom and a new page will appear with an order form to be filled.
- Fill in your paper’s requirements in the "
**PAPER DETAILS**" section. - Fill in your paper’s academic level, deadline, and the required number of pages from the drop-down menus.
- Click “
**CREATE ACCOUNT & SIGN IN**” to enter your registration details and get an account with us for record-keeping and then, click on “PROCEED TO CHECKOUT” at the bottom of the page. - From there, the payment sections will show, follow the guided payment process and your order will be available for our writing team to work on it.